Messaggio del 18-07-2007 alle ore 01:27:26

---

grazie tutto quello che ci allontana da wintel fa buon brodo

Messaggio del 17-07-2007 alle ore 20:56:06

---

giuseppe@giuseppe-desktop:~$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:0a.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
00:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62)
00:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62)
00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 65)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:0e.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2)

Messaggio del 17-07-2007 alle ore 20:54:30

---

giuseppe@giuseppe-desktop:~$ dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Thu Jun 7 20:19:32 UTC 2007 (Ubuntu 2.6.20-16.29-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001fef0000 end: 000000001fff0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001fff0000 size: 0000000000003000 end: 000000001fff3000 type: 4
[ 0.000000] copy_e820_map() start: 000000001fff3000 size: 000000000000d000 end: 0000000020000000 type: 3
[ 0.000000] copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[ 0.000000] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 131056) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 131056
[ 0.000000] HighMem 131056 -> 131056
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 131056
[ 0.000000] On node 0 totalpages: 131056
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 991 pages used for memmap
[ 0.000000] Normal zone: 125969 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 AWARD ) @ 0x000f7a30
[ 0.000000] ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
[ 0.000000] ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
[ 0.000000] ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
[ 0.000000] Detected 1466.758 MHz processor.
[ 37.852902] Built 1 zonelists. Total pages: 130033
[ 37.852908] Kernel command line: root=UUID=32156662-52ec-4b55-a9fc-c204faf7a6be ro quiet splash
[ 37.853139] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 37.853155] mapped APIC to ffffd000 (0140a000)
[ 37.853161] Enabling fast FPU save and restore... done.
[ 37.853164] Enabling unmasked SIMD FPU exception support... done.
[ 37.853184] Initializing CPU#0
[ 37.853304] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 37.854559] Console: colour VGA+ 80x25
[ 37.855310] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 37.855799] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 37.878410] Memory: 508728k/524224k available (1992k kernel code, 14968k reserved, 900k data, 328k init, 0k highmem)
[ 37.878425] virtual kernel memory layout:
[ 37.878426] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 37.878428] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 37.878430] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 37.878431] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 37.878433] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 37.878435] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB)
[ 37.878436] .text : 0xc0100000 - 0xc02f2374 (1992 kB)
[ 37.878441] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 37.957294] Calibrating delay using timer specific routine.. 2936.58 BogoMIPS (lpj=5873169)
[ 37.957360] Security Framework v1.0.0 initialized
[ 37.957372] SELinux: Disabled at boot.
[ 37.957398] Mount-cache hash table entries: 512
[ 37.957629] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[ 37.957642] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 37.957646] CPU: L2 Cache: 256K (64 bytes/line)
[ 37.957650] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[ 37.957666] Compat vDSO mapped to ffffe000.
[ 37.957674] Remapping vsyscall page to ffffe000
[ 37.957688] Checking 'hlt' instruction... OK.
[ 37.973482] SMP alternatives: switching to UP code
[ 37.973902] Freeing SMP alternatives: 11k freed
[ 37.974300] Early unpacking initramfs... done
[ 38.395954] ACPI: Core revision 20060707
[ 38.402912] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 38.404296] ACPI: setting ELCR to 0800 (from 0e20)
[ 38.609524] CPU0: AMD Athlon(tm) XP 1700+ stepping 02
[ 38.609533] SMP motherboard not detected.
[ 38.609537] Local APIC not detected. Using dummy APIC emulation.
[ 38.609613] Brought up 1 CPUs
[ 38.610026] Booting paravirtualized kernel on bare hardware
[ 38.610140] Time: 20:44:36 Date: 06/17/107
[ 38.610198] NET: Registered protocol family 16
[ 38.610365] EISA bus registered
[ 38.610372] ACPI: bus type pci registered
[ 38.642737] PCI: PCI BIOS revision 2.10 entry at 0xfb220, last bus=1
[ 38.642740] PCI: Using configuration type 1
[ 38.642743] Setting up standard PCI resources
[ 38.656254] ACPI: Interpreter enabled
[ 38.656260] ACPI: Using PIC for interrupt routing
[ 38.657010] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 38.657019] PCI: Probing PCI hardware (bus 00)
[ 38.657117] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 38.657571] PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
[ 38.657577] PCI quirk: region 5000-500f claimed by vt82c686 SMB
[ 38.657899] Boot video device is 0000:01:00.0
[ 38.657941] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 38.676342] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 38.676715] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[ 38.677091] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
[ 38.677477] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 38.680164] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 38.680187] pnp: PnP ACPI init
[ 38.683633] pnp: PnP ACPI: found 13 devices
[ 38.683641] PnPBIOS: Disabled by ACPI PNP
[ 38.683734] PCI: Using ACPI for IRQ routing
[ 38.683739] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 38.707155] NET: Registered protocol family 8
[ 38.707158] NET: Registered protocol family 20
[ 38.707996] PCI: Bridge: 0000:00:01.0
[ 38.707999] IO window: disabled.
[ 38.708005] MEM window: dc000000-ddffffff
[ 38.708010] PREFETCH window: d0000000-d7ffffff
[ 38.708028] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 38.708073] NET: Registered protocol family 2
[ 38.745318] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 38.745468] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 38.745816] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 38.746002] TCP: Hash tables configured (established 16384 bind 8192)
[ 38.746006] TCP reno registered
[ 38.757364] checking if image is initramfs... it is
[ 39.548181] Freeing initrd memory: 6768k freed
[ 39.548924] audit: initializing netlink socket (disabled)
[ 39.548950] audit(1184705077.676:1): initialized
[ 39.549144] VFS: Disk quotas dquot_6.5.1
[ 39.549179] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 39.549262] io scheduler noop registered
[ 39.549266] io scheduler anticipatory registered
[ 39.549269] io scheduler deadline registered
[ 39.549279] io scheduler cfq registered (default)
[ 39.549298] Applying VIA southbridge workaround.
[ 39.549303] PCI: Disabling Via external APIC routing
[ 39.549689] isapnp: Scanning for PnP cards...
[ 39.904034] isapnp: No Plug & Play device found
[ 39.945956] Real Time Clock Driver v1.12ac
[ 39.946026] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 39.946224] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 39.946609] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 39.947635] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 39.948157] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 39.948611] mice: PS/2 mouse device common for all mice
[ 39.949485] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 39.949875] input: Macintosh mouse button emulation as /class/input/input0
[ 39.949924] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 39.949930] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 39.950245] PNP: PS/2 Controller [PNP0303S2K,PNP0f13S2M] at 0x60,0x64 irq 1,12
[ 39.950676] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 39.950684] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 39.950863] EISA: Probing bus 0 at eisa.0
[ 39.950896] Cannot allocate resource for EISA slot 4
[ 39.950900] Cannot allocate resource for EISA slot 5
[ 39.950903] Cannot allocate resource for EISA slot 6
[ 39.950916] EISA: Detected 0 cards.
[ 39.981286] TCP cubic registered
[ 39.981298] NET: Registered protocol family 1
[ 39.981336] Using IPI No-Shortcut mode
[ 39.981478] ACPI: (supports S0 S1 S4 S5)
[ 39.981541] Magic number: 15:90:751
[ 39.981549] hash matches device ttyS2
[ 39.982459] Freeing unused kernel memory: 328k freed
[ 39.984960] Time: tsc clocksource has been installed.
[ 40.002334] input: AT Translated Set 2 keyboard as /class/input/input1
[ 41.271250] Capability LSM initialized
[ 41.328209] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 42.102694] SCSI subsystem initialized
[ 42.109844] libata version 2.20 loaded.
[ 42.113538] VP_IDE: IDE controller at PCI slot 0000:00:07.1
[ 42.113569] VP_IDE: chipset revision 6
[ 42.113572] VP_IDE: not 100% native mode: will probe irqs later
[ 42.113586] VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
[ 42.113597] ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hdaMA, hdbMA
[ 42.113613] ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdcMA, hddMA
[ 42.113623] Probing IDE interface ide0...
[ 42.136221] usbcore: registered new interface driver usbfs
[ 42.136262] usbcore: registered new interface driver hub
[ 42.136301] usbcore: registered new device driver usb
[ 42.137754] USB Universal Host Controller Interface driver v3.0
[ 42.321929] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 42.362498] Floppy drive(s): fd0 is 1.44M
[ 42.410595] FDC 0 is a post-1991 82077
[ 4.452000] Time: acpi_pm clocksource has been installed.
[ 4.492000] hda: IC35L040AVVN07-0, ATA DISK drive
[ 4.772000] hdb: Maxtor 92732U8, ATA DISK drive
[ 4.828000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.828000] Probing IDE interface ide1...
[ 5.692000] hdc: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
[ 6.476000] hdd: TOSHIBA DVD-ROM SD-R5112, ATAPI CD/DVD-ROM drive
[ 6.532000] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.536000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 6.536000] PCI: setting IRQ 11 as level-triggered
[ 6.536000] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 6.536000] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 6.540000] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 6.540000] uhci_hcd 0000:00:07.2: irq 11, io base 0x0000d400
[ 6.540000] usb usb1: configuration #1 chosen from 1 choice
[ 6.540000] hub 1-0:1.0: USB hub found
[ 6.540000] hub 1-0:1.0: 2 ports detected
[ 6.552000] hda: max request size: 128KiB
[ 6.576000] hda: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
[ 6.576000] hda: cache flushes supported
[ 6.576000] hda: hda1 hda2 < hda5 >
[ 6.596000] hdb: max request size: 128KiB
[ 6.612000] hdb: 53177040 sectors (27226 MB) w/2048KiB Cache, CHS=56272/15/63, UDMA(66)
[ 6.612000] hdb: cache flushes not supported
[ 6.612000] hdb: hdb1 hdb2 < hdb5 >
[ 6.644000] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 6.644000] uhci_hcd 0000:00:07.3: UHCI Host Controller
[ 6.644000] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[ 6.644000] uhci_hcd 0000:00:07.3: irq 11, io base 0x0000d800
[ 6.644000] usb usb2: configuration #1 chosen from 1 choice
[ 6.644000] hub 2-0:1.0: USB hub found
[ 6.644000] hub 2-0:1.0: 2 ports detected
[ 6.668000] hdc: ATAPI 44X DVD-ROM drive, 512kB Cache, UDMA(33)
[ 6.668000] Uniform CD-ROM driver Revision: 3.20
[ 6.672000] hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 6.748000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 6.748000] PCI: setting IRQ 10 as level-triggered
[ 6.748000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 6.748000] uhci_hcd 0000:00:0b.0: UHCI Host Controller
[ 6.748000] uhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3
[ 6.748000] uhci_hcd 0000:00:0b.0: irq 10, io base 0x0000e400
[ 6.748000] usb usb3: configuration #1 chosen from 1 choice
[ 6.748000] hub 3-0:1.0: USB hub found
[ 6.748000] hub 3-0:1.0: 2 ports detected
[ 6.852000] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 6.852000] uhci_hcd 0000:00:0b.1: UHCI Host Controller
[ 6.852000] uhci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 4
[ 6.852000] uhci_hcd 0000:00:0b.1: irq 11, io base 0x0000e800
[ 6.852000] usb usb4: configuration #1 chosen from 1 choice
[ 6.852000] hub 4-0:1.0: USB hub found
[ 6.852000] hub 4-0:1.0: 2 ports detected
[ 6.956000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 6.956000] ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 6.956000] ehci_hcd 0000:00:0b.2: EHCI Host Controller
[ 6.956000] ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 5
[ 6.956000] ehci_hcd 0000:00:0b.2: irq 10, io mem 0xde000000
[ 6.956000] ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 6.956000] usb usb5: configuration #1 chosen from 1 choice
[ 6.956000] hub 5-0:1.0: USB hub found
[ 6.956000] hub 5-0:1.0: 4 ports detected
[ 7.060000] 8139cp 0000:00:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 7.060000] 8139cp 0000:00:0c.0: Try the "8139too" driver instead.
[ 7.060000] 8139too Fast Ethernet driver 0.9.28
[ 7.060000] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 7.060000] eth0: RealTek RTL8139 at 0xe084e000, 00:40:f4:69:6f:b7, IRQ 11
[ 7.060000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 7.132000] Attempting manual resume
[ 7.132000] swsusp: Resume From Partition 3:69
[ 7.132000] PM: Checking swsusp image.
[ 7.140000] PM: Resume from disk failed.
[ 7.196000] kjournald starting. Commit interval 5 seconds
[ 7.196000] EXT3-fs: mounted filesystem with ordered data mode.
[ 7.908000] usb 5-1: new high speed USB device using ehci_hcd and address 2
[ 8.040000] usb 5-1: configuration #1 chosen from 1 choice
[ 20.488000] eth0: link down
[ 20.900000] NET: Registered protocol family 10
[ 20.900000] lo: Disabled Privacy Extensions
[ 20.900000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.312000] parport_pc: VIA 686A/8231 detected
[ 23.312000] parport_pc: probing current configuration
[ 23.312000] parport_pc: Current parallel port base: 0x378
[ 23.312000] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 23.724000] parport_pc: VIA parallel port: io=0x378, irq=7
[ 23.892000] Linux agpgart interface v0.102 (c) Dave Jones
[ 23.936000] Linux video capture interface: v2.00
[ 24.008000] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 24.008000] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[ 24.008000] PCI: setting IRQ 5 as level-triggered
[ 24.008000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 24.008000] saa7133[0]: found at 0000:00:0e.0, rev: 209, irq: 5, latency: 32, mmio: 0xde002000
[ 24.008000] saa7133[0]: subsystem: 4e42:3306, board: LifeView FlyDVB-T Hybrid Cardbus [card=94,insmod option]
[ 24.008000] saa7133[0]: board init: gpio is 210000
[ 24.060000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 24.080000] input: PC Speaker as /class/input/input2
[ 24.144000] saa7133[0]: i2c eeprom 00: 42 4e 06 33 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[ 24.144000] saa7133[0]: i2c eeprom 10: 00 00 62 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[ 24.144000] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 ed ff ff ff ff
[ 24.144000] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 24.144000] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 05 01 01 16 32 15 ff ff ff ff
[ 24.144000] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 24.144000] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 24.144000] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 24.152000] saa7133[0]: i2c scan: found device @ 0x10 [???]
[ 24.168000] saa7133[0]: i2c scan: found device @ 0x96 [???]
[ 24.176000] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
[ 24.296000] tuner 1-004b: chip found @ 0x96 (saa7133[0])
[ 24.344000] tuner 1-004b: setting tuner address to 61
[ 24.384000] tuner 1-004b: type set to tda8290+75a
[ 24.496000] tuner 1-004b: setting tuner address to 61
[ 24.536000] tuner 1-004b: type set to tda8290+75a
[ 24.600000] saa7133[0]: registered device video0 [v4l2]
[ 24.600000] saa7133[0]: registered device vbi0
[ 24.600000] saa7133[0]: registered device radio0
[ 24.628000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 24.628000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[ 24.632000] agpgart: AGP aperture is 64M @ 0xd8000000
[ 24.696000] ieee80211_crypt: registered algorithm 'NULL'
[ 24.696000] input: PS2++ Logitech Wheel Mouse as /class/input/input3
[ 24.720000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 24.720000] ieee80211: Copyright (C) 2004-2005 Intel Corporation
[ 25.008000] saa7134 ALSA driver for DMA sound loaded
[ 25.008000] saa7133[0]/alsa: saa7133[0] at 0xde002000 irq 5 registered as card -2
[ 25.128000] nvidia: module license 'NVIDIA' taints kernel.
[ 25.400000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 25.400000] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006
[ 25.744000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 26.256000] zd1211rw 5-1:1.0: firmware version 4725
[ 26.296000] zd1211rw 5-1:1.0: zd1211b chip 0ace:1215 v4810 high 00-02-72 AL2230_RF pa0 g--N
[ 26.300000] zd1211rw 5-1:1.0: eth1
[ 26.300000] usbcore: registered new interface driver zd1211rw
[ 26.368000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 26.420000] ieee80211_crypt: registered algorithm 'WEP'
[ 27.048000] SoftMAC: Open Authentication completed with 00:14:7f:6b:03:78
[ 28.536000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 34.380000] fuse init (API version 7.8)
[ 34.428000] lp0: using parport0 (interrupt-driven).
[ 34.500000] Adding 1140572k swap on /dev/disk/by-uuid/59b4284e-57b1-48b7-bdbe-f71927546413. Priority:-1 extents:1 across:1140572k
[ 34.672000] EXT3 FS on hdb1, internal journal
[ 36.840000] NET: Registered protocol family 17
[ 39.260000] eth1: no IPv6 routers present
[ 40.620000] input: Power Button (FF) as /class/input/input4
[ 40.620000] ACPI: Power Button (FF) [PWRF]
[ 40.672000] input: Power Button (CM) as /class/input/input5
[ 40.672000] ACPI: Power Button (CM) [PWRB]
[ 40.696000] input: Sleep Button (CM) as /class/input/input6
[ 40.696000] ACPI: Sleep Button (CM) [SLPB]
[ 41.088000] No dock devices found.
[ 41.172000] ibm_acpi: ec object not found
[ 41.236000] Using specific hotkey driver
[ 41.520000] pcc_acpi: loading...
[ 46.932000] ppdev: user-space parallel port driver
[ 47.156000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 47.156000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 47.156000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 49.932000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 49.932000] apm: overridden by ACPI.
[ 52.372000] DVB: registering new adapter (saa7133[0]).
[ 52.372000] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
[ 81.528000] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 81.572000] ISOFS: changing to secondary root
[ 277.232000] cdrom: This disc doesn't have any tracks I recognize!

Messaggio del 17-07-2007 alle ore 11:08:17

---

cmq, per curiosita' mi manderesti l'output del comando dmesg e di lspci?

Messaggio del 17-07-2007 alle ore 11:06:10

---

exit, esce .....!

Messaggio del 17-07-2007 alle ore 09:49:45

---

Eh... il Win... buono quello! Non mi ha nemmeno riconosciuto la scheda TV... con il driver originale della scheda mi da' errore e non installa una cippa...

Poi tra le altre cose ho provato DeVeDe con Xubuntu per creare DVD video da un file avi/mpg... fantastico! Un unico passaggio senza tante complicazioni; avevo provato a farlo su Win, ma (a parte che ci volevano programmi commerciali ) si dovevano settare bitrate e ca**i vari... creare prima il mpeg2, poi fare l'authoring...

Poi pure il collegamento wireless (sullo stesso PC e con la medesima scheda WiFi che uso con Xubuntu) con Win ogni tanto si perde e all'accensione del PC ci mette un'eternita' prima di stabilizzare il collegamento WiFi; invece Xubuntu senza incertezze stabilizza il collegamento e non si schioda...

Messaggio del 16-07-2007 alle ore 21:46:39

---

Passa a Windows che fai prima

Messaggio del 16-07-2007 alle ore 21:19:59

---

Ho scoperto il mistero...

exit 0 va scritto dopo i comandi...

Cmq ora funzia tutto... anche se penso di aver incasinato un po' i vari file /etc/modules, /etc/modprobe.d/options, /etc/modprobe.d/aliases perche' _putroppo_ ho dovuto prendere comandi un po' qui un po' li' dai vari forum, blog ecc....

Grassie dell'aiuto...

Adesso il "noccio" peggiore... configurare mythTV...aiutoooooooooo

stay tuned...

Messaggio del 16-07-2007 alle ore 20:23:26

---

Devi cambiare i permessi dello script, evidentemente ti servono i permessi da root che quando cerca di caricare il modulo non ha...
Il comando per cambiare i permessi è chmod, vedi un pò per quale utente ti serve e per cosa ti serve, googlando un pò trovi come usarlo...

Messaggio del 16-07-2007 alle ore 19:32:14

---

Si' george... scusate avrei dovuto scrivere i numeri (ad uso di chi dovesse fare una ricerca su google). Allora il numero della card per Lifeview FlyDVB-T Hybrid (interna PCI) è 94 e il tuner e' 54.

Ho provato a modificare come dici tu george il file rc.local cosi'...

#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

exit 0
modprobe saa7134 i2c_scan=1 card=94 tuner=54
modprobe saa7134_alsa
modprobe saa7134_dvb

Solo che non va... devo sempre dare il comando manualmente e solo allora il dvb-t funziona... io non e' ci capisco granche' ma mi pare di leggere dall'intestazione del file che bisogna "change the execution bits" per abilitare lo script... ho provato pure a rimuovere il cancelletto all'inizio dello script... ma niente... bho???

Insomma devo automatizzare il comando "modprobe saa7134_dvb" come fare? Help me please...

Messaggio del 16-07-2007 alle ore 17:53:40

---

dallo script che hai eseguito:


modprobe saa7134 card=94 tuner=$i


hai trovato quale tuner devi usare?...

nel caso puoi (per esempio) aggiungere il comando in /etc/rc.local

Messaggio del 16-07-2007 alle ore 17:30:31

---

Allora... grazie a chi mi ha risposto...

La scheda pare che funziona seguendo le istruzioni del wiki... almeno con TVtime (non riuscivo a vedere nulla perche' probabilmente mancava i2c_scan=1 quando specificavo il tipo di scheda e il numero del tuner...

Pero' perche' funzioni la TV digitale con Kaffeine e' necessario dare il seguente comando:

sudo modprobe saa7134_dvb

Domanda: come faccio a passare questo comando in modo che venga caricato all'inizio? Suppongo che i linuxiani del forum aspranno rispodermi in un attmo

Ho provato sia aggiungendo le istruzioni in /etc/modprobe.conf, sia aggiungendo un file con le stesse istruzioni nella cartella /etc/modprobe.d (come ho trovato da qualche parte...) ma non funziona... devo dare manualmente il comando sudo modprobe saa7134_dvb

Grazie in anticipo

Messaggio del 12-07-2007 alle ore 02:23:52

---

passa a Windows!

Messaggio del 12-07-2007 alle ore 02:22:29

---

Prendi il tempo nelle tue mani: passa a Windows!

Messaggio del 11-07-2007 alle ore 21:31:21

---

dmesg e lspci che dicono ?

Messaggio del 11-07-2007 alle ore 09:09:28

---

Grazie del pensiero

Messaggio del 10-07-2007 alle ore 21:25:07

---

vorrei aiutarti ma nn ho capito un cazzo

Messaggio del 10-07-2007 alle ore 10:38:06

---

Come ho scritto tempo fa su un altro post ho installato Xubuntu (feisty)... tutto Ok (o quasi.... qualche impiccio poi risolto con l'aiuto online...).

Ho deciso di installare una scheda TV e ho comprato la Lifeview FlyDVB-T Hybrid (interna PCI) per tentare di trasformare il PC in un mediacenter con MythTV

Ho seguito le istruzioni qui: http://wiki.ubuntu-it.org/SchedeTvHowto

Si tratta di modificare i seguenti files:

/etc/modules
/etc/modprobe.d/options
/etc/modprobe.d/aliases

come da istruzioni e come ultimo passo nel file options aggiungere la seguente riga:

options saa7134 card=[numero della vostra scheda] tuner=[numero del tuner].

Orbene il numero della scheda e' 94 (nella lista il mio modello ha quel numero), ma il numero del tuner sembra introvabile. Ho provato qualche numero, ma nisba... il tvtime parte, ho la schermata blu "television", ma c'e' la scritta "No signal" (la scheda dopvrebbe essere stata riconosciuta anche perche' il dmesg mi da' il nome della scheda - che prima era denominata "generic", inoltre e' presente il modulo saa7134.ko) e i canali non si sintonizzano ne' con l'antennina incorporata della scheda, ne' con quella "aerial" centralizzata di casa.

Allora ho rimesso tutto come prima della modifica "schedeHowto" e ho provato questo script che ho trovato in un forum

#/bin/sh
MAXTUNER=69
i=0

while [ $i -lt $MAXTUNER ];
do
rmmod saa7134_alsa saa7134
modprobe saa7134 card=94 tuner=$i
echo "Actual tuner is:" $i
sleep 1 # this is to make sure /dev/video is registered when tvtime starts
tvtime
i=$(($i+1))
done

per provare tutti i numeri di tuner possibili... ma niente, non va: ottengo sempre la schermata di tvtime che la scheda sembra riconosciuta, ma la sintonizzazione non va. In pratica lo script carica e scarica il modulo (credo) con un numero diverso di tuner ogni volta e prova tvtime per verificarne la funzionalita'. Ho provato a sintonizzare per tutte le volte che il tvtime viene eseguito dallo script senza successo. Per alcuni tuner il conteggio dei canali va avanti ma senza sintonizzazione, mentre per altri tutto e' immobile...

Ho girato google e i vari forum i lungo e in largo... ma senza successo. Di solito riesco (pur con conoscenze limitatissime di linux e in generale di computer) a trovare le soluzioni, ma stavolta e' davvero frustrante...

L'unica cosa che forse potrebbe essere e' il passaggio spiegato nel wikiHowto dove si dice di cercare nel file aliases la riga contenente i2c, cancellarla e sostituirla con "alias char-major-89 i2c-dev" (dopo aver cabmiato la riga ottengo un errore quando il modulo viene caricato... forse il wiki ha un'istruzione errata?)

Qualcuno ha avuto espierenze di utilizzo di schede del genere?

Forse che a Villa Scorciosa non c'e' il segnale DVB? Ma almeno quello analogico...

Purtroppo non posso verificare nemmeno il segnale con il WindowsXP perche' si rifiuta di installare il driver della scheda...(e non so perche'...)

Qualcuno puo' please darmi una mano?